Glass Tube Cutting Tips

Mar 28, 2022 Leave a message

glass tube.jpg

 Glass Tube Cutting Tips

  • 1. Cutting of flat glass

  • The cutting of flat glass must first determine the cutting size on the glass to be cut and mark it. If the cutting line can be aligned with a ruler, the distance between the tip of the glass knife and the edge is about 2mm, so the ruler should be withdrawn by 2mm when cutting the knife.

  • When cutting glass, you should hold the knife with the right hand and press the ruler with the left hand, so that the side of the glass knife is against the wooden ruler to cut. After cutting, what is left on the glass is only a nick, not a cut through the glass. Therefore, when cutting glass, as long as traces are left on the glass. Don't count knives in the same place. If the cutting operation is improper and the notch is too shallow, it should be cut on the reverse side of the glass. If the notch is too shallow, it is not easy to break the glass, you can use a glass knife, pliers, small hammer, etc. to strike from the bottom to the top at the center line of the glass on the back of the notch, until a crack appears at the scratch, and then break it hard. Rounding and edging of flat glass. If the thickness of flat glass with curved or round outer edge is less than 3mm, you can use the above scribing method to make the desired notch first, and then put it in clean water and cut it into the desired shape with scissors. After cutting, round the edges with water sandpaper or grindstone, fine grinding wheel, etc. in water.

  • 2. Cutting of glass pipes

  • Cutting of thin glass tubes and rods. When cutting thin glass tubes and rods with a diameter of 5mm-10mm or less, they should first be placed flat on the edge of the table, and the edge of the triangular file, grinding wheel (or newly broken porcelain bowl) should be pressed vertically on the glass tube. When you want to cut off, push it forward so that the file mark reaches 1/3 or 1/4 of the circumference of the tube, pick up the glass tube (rod), and press the thumbs of both hands against the back of the file mark. The remaining fingers hold the glass tube (rod), and pull back with both hands at the same time to break.

  • Cutting of rough glass tubes. First, use a file to file a circle of fine marks at the place to be cut, and use a resistance wire to surround the fine marks. The intersection of the resistance wires are separated by heat-resistant insulating materials (or leave a small gap of 1mm-2mm). The resistance wire can be drawn from the 150W electric furnace wire. Take a section of it and heat it straight. The resistance wire can be adjusted to a very low voltage supply by a voltage regulator or a low-voltage power supply. Wait a minute or so for the resistance wire to be red hot. Drop a drop of cold water on the fine marks, and at the same time power off, the glass tube will be broken along the fine marks.

  • The broken glass tube orifice is very sharp and easy to scratch the skin, so do some treatment after the glass is broken. The first method is to burn it smooth on an alcohol lamp; the other is to smooth it on a fine emery cloth or a grindstone.

  • 3. Cutting of glass bottles

  • There are many ways to cut glass bottles (waste bulbs), and several methods are described below.

  • Use a glass knife or a wind file to carve a file mark at the cutting place of the glass bottle, then wrap a cotton thread around the file mark a few times, then drop alcohol, ignite the cotton thread for about a minute, and drop a few drops of water at the file mark. It can be broken along the file mark.

  • Cut the waste newspaper into 5mm-7mm wide strips, then soak the paper strips in clean water and take them out. The soaked strip of paper is 1-4 circles around the circumference of the bottle along the cutting line of the glass bottle. The edge of the newspaper must be neat. Light the alcohol lamp, align the cutting line of the bottle with the flame of the alcohol lamp, and keep turning the bottle. When the bottle is hot, it can be disconnected by placing it in cold water.

  • Fill the glass bottle with cooking oil to the cutting line (and leave the iron bar allowance), then insert the red iron bar into the oil, and the glass bottle will be broken along the oil surface.

  • Glass bottles, glass tubes, light bulbs, etc. can also be cut with a homemade resistance wire cutter. Pay attention when cutting: First, leave a space of 1mm-2mm at the intersection of the resistance wire to avoid short circuit. The second is to quickly cut off the power after the glass bottle is dripping.