1, the glass tube level gauge in transportation, handling and installation, can not impact or knock, to prevent the glass tube and glass broken.
2, after installation, when the medium temperature is very high, do not open the valve immediately, should preheat 20-30 minutes, after the glass tube has a certain temperature, and then slowly open the valve. Valve opening procedure: first slowly open the upper valve, and then slowly open the lower valve, so that the measured medium slowly into the glass tube.
3. In use, the dirt on the inner and outer walls of the glass tube should be cleaned regularly to keep the liquid level display clear. Cleaning procedure: First close the upper and lower valves connected with the container, open the drain valve, clean the residual liquid in the glass tube, use the appropriate cleaning agent or use the long rod hair brush and wipe method to remove the dirt on the inner wall of the tube.
4, if the quartz tube is broken or seriously need to be replaced, the specific steps: remove the watch body, unscrew the nuts and nuts at both ends, knock the quartz glass tube from one end to the other end with a stick, take out the graphite ring, put the new quartz tube into the graphite ring, and then put the graphite ring on the quartz tube, embed the watch body equidistant, tighten the nuts and nuts at both ends, and confirm that there is no leakage, you can put into operation.
1, the glass tube level gauge in transportation, handling and installation, can not impact or knock, to prevent the glass tube and glass broken.
2, after installation, when the medium temperature is very high, do not open the valve immediately, should preheat 20-30 minutes, after the glass tube has a certain temperature, and then slowly open the valve. Valve opening procedure: first slowly open the upper valve, and then slowly open the lower valve, so that the measured medium slowly into the glass tube.
3. In use, the dirt on the inner and outer walls of the glass tube should be cleaned regularly to keep the liquid level display clear. Cleaning procedure: First close the upper and lower valves connected with the container, open the drain valve, clean the residual liquid in the glass tube, use the appropriate cleaning agent or use the long rod hair brush and wipe method to remove the dirt on the inner wall of the tube.
4, if the quartz tube is broken or seriously need to be replaced, the specific steps: remove the watch body, unscrew the nuts and nuts at both ends, knock the quartz glass tube from one end to the other end with a stick, take out the graphite ring, put the new quartz tube into the graphite ring, and then put the graphite ring on the quartz tube, embed the watch body equidistant, tighten the nuts and nuts at both ends, and confirm that there is no leakage, you can put into operation.
1, the glass tube level gauge in transportation, handling and installation, can not impact or knock, to prevent the glass tube and glass broken.
2, after installation, when the medium temperature is very high, do not open the valve immediately, should preheat 20-30 minutes, after the glass tube has a certain temperature, and then slowly open the valve. Valve opening procedure: first slowly open the upper valve, and then slowly open the lower valve, so that the measured medium slowly into the glass tube.
3. In use, the dirt on the inner and outer walls of the glass tube should be cleaned regularly to keep the liquid level display clear. Cleaning procedure: First close the upper and lower valves connected with the container, open the drain valve, clean the residual liquid in the glass tube, use the appropriate cleaning agent or use the long rod hair brush and wipe method to remove the dirt on the inner wall of the tube.
4, if the quartz tube is broken or seriously need to be replaced, the specific steps: remove the watch body, unscrew the nuts and nuts at both ends, knock the quartz glass tube from one end to the other end with a stick, take out the graphite ring, put the new quartz tube into the graphite ring, and then put the graphite ring on the quartz tube, embed the watch body equidistant, tighten the nuts and nuts at both ends, and confirm that there is no leakage, you can put into operation.
1, the glass tube level gauge in transportation, handling and installation, can not impact or knock, to prevent the glass tube and glass broken.
2, after installation, when the medium temperature is very high, do not open the valve immediately, should preheat 20-30 minutes, after the glass tube has a certain temperature, and then slowly open the valve. Valve opening procedure: first slowly open the upper valve, and then slowly open the lower valve, so that the measured medium slowly into the glass tube.
3. In use, the dirt on the inner and outer walls of the glass tube should be cleaned regularly to keep the liquid level display clear. Cleaning procedure: First close the upper and lower valves connected with the container, open the drain valve, clean the residual liquid in the glass tube, use the appropriate cleaning agent or use the long rod hair brush and wipe method to remove the dirt on the inner wall of the tube.
4, if the quartz tube is broken or seriously need to be replaced, the specific steps: remove the watch body, unscrew the nuts and nuts at both ends, knock the quartz glass tube from one end to the other end with a stick, take out the graphite ring, put the new quartz tube into the graphite ring, and then put the graphite ring on the quartz tube, embed the watch body equidistant, tighten the nuts and nuts at both ends, and confirm that there is no leakage, you can put into operation.
